The process of altering the structure of metal so as to relieve it’s working stresses and increase it’s ductivity.
A metallic part of the primer. The blow from the firing pin crushes the priming mixture against the anvil causing ignition.
In military nomenclature this term refers to the bullet.
This is a trade name for a double-base smokeless powder developed by Olin Industries. The grains have a spherical, or flattened spherical shape.
The science of projectiles in motion.
Ratio of the sectional density of a bullet to its coefficient form. Represents the projectiles ability to overcome air resistance in flight.
A type of primer used in shotshells which makes use of an outside cup to support it in the case.
That portion of the bullet surface which bears on, or touches, the bore.
To open the mouth of a case slightly in order to seat a bullet more easily. Also used in reference to a rifle barrel which is worn at the muzzle (belled muzzle).
A band which is formed into the head of some cases (magnum type) to strengthen the case and headspace of the cartridge.
A common European priming system which makes use of an anvil formed in the case itself.
A bullet design having a tapered base.
The inside diameter of a barrel before the rifling is cut.
A type of primer used in all American rifle and pistol ammunition and featuring a self contained anvil. It is fitted in the primer pocket in the head of centerfire cartridge cases.
That portion of the cartridge which becomes a projectile when in flight.
A term which is used to describe the rapidity with which a given powder will burn. The term itself is a relative one based on a comparison with other powders.
The approximate diameter of a bullet or bore, expressed in decimals of an inch in English. In Europe, where the metric system is used, this measurement is expressed in millimeter.
A groove (or grooves) cut around the circumference of a bullet. These grooves, usually one to a bullet, provide the best means of securely crimping the case mouth into the bullet.
The metal, plastic or paper container which holds all of the components of a round of ammunition.
Case Neck Brush:
The metal or nylon brush and handle used to clean the inside of case necks.
A device used to remove excess material from a case mouth. Metallic cases stretch after extensive reloading and firing because the brass flows forward. These cases must be trimmed back.
Case Trimmer Pilot:
The pilot guides the cutting portion of the case trimmer by fitting inside the neck of the case to be trimmed.
Bullets for centerfire rifle or pistol which are cast from lead alloy. Muzzleloading projectiles and shotgun slugs are cast in pure lead.
Refers to a cartridge having a centrally located primer in it’s base.
The part of the bore at the breech which is formed to accept and support the loaded cartridge.
To ream a taper on the inside of a case mouth.
The amount of powder used in the case at each loading. Also refers to the amount of shot used in a shotshell.
A constriction at the muzzle of a shotgun barrel designed to control the spreading of shot.
An instrument used to measure the velocity of a projectile.
A charge of powder which so nearly fills the case that it is compressed when the bullet is seated.
Any of the various parts which go into the making of a cartridge.
The eating away of the bore by rust or chemical action.
The bending inward of the case mouth to grip the bullet. With shotshells the term applies to the closure at the case mouth.
A forcing inward of the brass around the top of the primer pocket. This is frequently found on military cartridges and is done to prevent set-back of primers. The crimp must be removed before repriming the case.
The deburring tool removes burs from the inside and outside of any newly trimmed case mouths
To deprime a case by removing the spent primer from the primer pocket, most often accomplished by the decapping pin in a die during the resizing operation of reloading.
A tool, in handloading, that reforms cartridge cases and seats bullets; or, in bullet manufacture, a tool that swages bullets or cores, extrudes lead wire or draws jackets.
Term used to indicate the approximate velocity of a shot charge by comparison.
Deviation of a projectile from the line of departure due to its rotational spin or the force of wind.
The distance a projectile falls, calculated from the line of departure.
Double Base Powder:
Smokeless powder made with nitroglycerine and nitrocellulose base.
The use of two different powders in loading the same cartridge.
A projectile’s capacity for doing work at a given range, expressed in foot-pounds.
The wearing away of the bore due to friction and/or gas cutting.
Reforming or changing the shape of a cartridge case by firing it in a chamber of a desired shape.
A hole leading from the primer pocket to the inside of a case.
A unit of kinetic energy equal to the effort required to raise one pound of weight; to put a height of one foot, against the normal pull of gravity.
The distance in the barrel, if any, which the bullet travels before it contacts the rifling. Some barrels are purposely relieved to allow the bullet considerable free movement before it strikes the rifling.
A gliding metal cup which is used to protect the base of a cast lead alloy bullet from the effects of burning powder gases.
A copper-zinc alloy used for bullet jackets and gas checks.
A unit of weight measure. 437.5 grains equal one ounce; 7000 grains equal one pound.
The distance from the breech face to the part of the chamber which acts as a stop and prevents the cartridge from moving forward. Also applies to the cartridge case.
The outer edge of the bullet base.
A bullet design which features an axial hole at the point. The purpose of the hole is to aid expansion on impact.
The action of setting the powder charge on fire.
Abbreviation for “Improved Military Rifle”.
The covering or “skin” of a bullet.
The imprint of a bullet which struck sideways on target rather than point first.
The raised portion of the rifling.
Line of Sight:
An imaginary straight line from the eye, through the sights, to the point of aim.
Ratio of the volume of the powder charge to the volume of the case. The higher the better in terms of accuracy.
A dent in the cartridge case caused by using too much lubricant when resizing.
A pad, impregnated with lubricant, on which cases are rolled before resizing.
Case sizing lubricant is used to reduce friction between the case and die during the resizing operation in reloading.
A primer in which the priming material contains mercury.
Metal Case (MC):
A type of bullet which, except for a small opening at the base, is completely encased in a jacket.
Refers to the distance the bullet rises above the line of sight. Mid-range trajectory is calculated halfway between the muzzle and the target.
A unit of angular deviation equal to 1/60th of a degree. For practical purposes, it is usually approximated as equal to one inch at 100 yards.
The failure of a cartridge to fire after the primer was struck.
The front end of the barrel.
The upper portion of a cartridge case that grips the bullet.
To resize only the neck portion of a case.
Usually refers to primers having a priming mixture which is free of corrosive compounds. Modern primers are non-corrosive.
Refers to the nose shape of the bullet. The radius of the curve of a bullet nose.
The propellant used in most firearms. It produces a large volume of gas when ignited. There are two basic types; smokeless and black powder.
A helpful accessory that facilitates transfer of powder from a scale pan or measure to a cartridge case.
An adjustable volumetric measure that meters out uniform charges of powder.
A device to weigh charges of powder. A beam scale is a scale where markers, called “poise”, are moved along a weight graduated beam, as the pan is filled with powder, until the balance point is reached. An electronic device used to measure the weight of powder in grains or grams.
The force exerted by a burning charge of a powder in the chamber of a firearm. Expressed normally in pounds per square inch.
A small metal cap containing the detonating mixture which is used to ignite the propellant charge.
The cavity in the base of a cartridge which receive and supports the primer.
The main shaft of a metallic cartridge reloading tool.
The reloading die that resizes fired cartridge cases and removes spent primers by means of a decapping pin.
A military term meaning one single cartridge.
Round Nose (RN):
A bullet design which features a rounded nose.
An abbreviation for “Sporting Arms and Ammunition Manufacturers Institute”.
The depth to which a bullet is seated below the case mouth.
The reloading die that presses the bullet into the neck of the cartridge case, crimping the case if so desired.
A bullets weight, in pounds, divided by the square of it’s diameter in inches.
This is attached to the top of the ram and holds the heads of the cartridge cases as they are moved up and down, into and out of the die.
To pressure-form by forcing through or into a die.
That area of the bore immediately ahead of the chamber.
The path of a projectile in flight.
The length a cartridge case should be trimmed to after it has stretched past it’s maximum case length.
A reloading press with a rotatable multi station turret top for positioning dies and powder measure in their appropriate sequence.
The speed at which a projectile travels. Usually measured in feet per second at a given range.
A slide-type graduated instrument used to measure overall cartridge and case lengths precisely.
Wad Cutter (WC):
A bullet design which features a sharp shoulder. Designed to cut a clean round hole in a paper target.
That portion of a cartridge case between the bottom of the primer pocket and the interior of the case.
Brass becomes harder as it is worked. See “Anneal”.
Center of a target. Bulls-eye.
The action of a projectile spinning erratically around it’s own axis.
The ranges at which a firearm will hit the point of aim.